S960171AA Armitage Shanks Avon Valve / Metering Cap Self Closing Tap Cartridge (Ideal Standard)

+ $26.49 Shipping

S960171AA Armitage Shanks Avon Valve / Metering Cap Self Closing Tap Cartridge (Ideal Standard)

RRP: $119.00
Price: $84.00
You save: $35.00 (29%)
$84.00 + $26.49 Shipping

Taxes calculated at checkout

Only 1 left in stock

Dispatched within 24 hours

We accept the following payment methods


S960171AA Armitage Shanks / Ideal Standard / Trevi Avon Valve / Metering Cap CartridgeArmitage Shanks / Ideal Standard S960171AA Measurements and other Information Measurements:Total Length: 76.9mm (When not compressed) Width of Top Toothed Spline (from tooth to tooth): 24.9mm Width at Widest Point: 32.9mm (the O Ring in the middle) Width at Thread (below o ring): 31.6mm Possible Markings: LH, A9924459 Other information: Manufacturer: Armitage Shanks / Ideal Standard Spare Part: Metering Tap Cartridge Spare Part - S960171AA Installation: Screw-Fit This S960171AA cartridge is used on the following taps: - B8267AA Avon 21 Basin Pillar Taps Self Closing - S7239AA Avon pair self closing basin taps - S7241AA Avon Bibtap Chrome Non Con Lg / AshPressThe pair of hot and cold handle caps for the Avon Self Closing tap is spare part number S960167AA.Armitage Shanks S960171AA Cartridge Removal and Replacement for Avon 21 Basin Pillar Tap (B8267AA) 1. Isolate or switch off hot and cold water supplies. Plug the sink’s drain to keep screws from plunging in. 2. Prise out the screw cap located behind the tap handle. Use a 2.5mm Allen key to remove the grub screw. 3. Lift the handle to remove. 4. Unscrew the chrome covering with a 41mm A/F spanner. Remove it together with the adjustment ring. 5. Pull the cartridge out. The brass housing will come out with the cartridge. 6. Use a 22mm A/F spanner to screw the faulty cartridge out of the housing. 7. Scan the inside of the tap unit for dirt and debris. Clean the valve seat if it is necessary.8. Grease the O-ring of the S960171AA Armitage Shanks / Ideal Standard cartridge spare part with silicone grease before setting it in the brass housing. 9. Use the spanner to tighten the new Armitage Shanks S960171AA replacement metering cartridge in the brass housing. The ideal torque is 15Nm. Be careful not to damage the parts. 9. Introduce the cartridge with the brass housing in the tap valve. See to it the lobe portion of the housing is installed towards the back of the tap valve. 10. Return the chrome cover with adjustment ring. Tighten with a spanner. The recommended torque is 15Nm. 11. Fine-tune the run time if desired. 12. Refit the handle, the grub screw, and the screw cover. 13. Turn on the hot and cold water supplies. Adjusting the Run Time of the S960171AA Metering Tap Cartridge The run time of the Armitage Shanks Avon tap models is about 5 to 15 seconds. If you desire a longer run time, remove the handle and use the “run time adjustment key” which was provided with the tap unit. – Turning the key clockwise will increase the run time. – Turning it the opposite direction will shorten the run time. Restore the handle and check if run time is sufficient. Lock the handle in position using the grub screw and Allen key.
  • Fruugo ID: 12561485-25132379
  • Sold by: Di Vapor

Delivery & Returns

Di Vapor

Address: Colwall Lodge Marsh Lane, Solihull, B91 2PQ, United Kingdom
Retailer VRN: GB892423900
Company Number: GB892423900
All products: Visit Di Vapor Shop