FrSky 8 ch telemetry 2,4Ghz, ACCST, D8R-XP

$36.95 Only 1 item left in stock
Quantity:
  • Product reference: 4164661-9562309
  • Plane icon Dispatched within 24 hours
  • Shipping from Finland
  • Delivery cost to USA $8.87

FEATURES 1) Two external analog telemetry ports (A1&A2) and one digital data-stream port (Rx) 2) RSSI (PWM) and CPPM output - If CH3 and CH4 are connected by a jumper, CH1 will output CPPM for CH1~CH8, and CH2 will output RSSI (PWM) 3) When side port pins of A1 and X are connected by the jumper, A1 will change from external analog telemetry port to internal built-in battery voltage sensor 4) Firmware upgradeable 5) Alarm warning on low voltage, poor reception, etc.   1. Introduction 1.1 Compatibility     Compatible with FrSky two way telemetry modules: DFT, DJT, DHT, DHT-U 1.2 Specifications     Dimension: 55*25*14mm     Weight: 12.4g     Operating Voltage Range: 3.5V-10.0V     Operating Current: 100mA     Operating Range: full range (>1.5km)     Servo Frame Rate: 18ms (FS – Normal Speed Mode)                                          9ms (HS – High Speed Mode)                      1.3 Features     1) Two external analog telemetry ports (A1&A2) and one digital data-stream port (Rx);     2) When side port pins of A1 and X are connected by the jumper, A1 will change from external          analog telemetry port to internal built-in battery voltage sensor;     3) Convenient to upgrade – no need to open the receiver’s case when upgrade D8R-II plus;     4) Two switchable PPM modes - FS mode and HS mode;     5) Alarm warning on low voltage, poor reception, etc.   2. Set up 2.1 Bind procedure     1) Ascertain that the transmitter is in the PPM mode. Turn off the transmitter.     2) Turn on the transmitter while holding the F/S button on the transmitter module (Ensure that          both switches on the transmitter module are OFF when using D8R-II plus in two way mode).          Release the button. The RED LED on the transmitter module will flash, indicating the          transmitter is ready to bind to the receiver.     3) Connect battery to the receiver while holding the F/S button on the receiver. The RED LED on          the receiver will flash, indicating the binding process is completed. Turn off both the transmitter          and the receiver.     4) Turn on the transmitter and connect the battery to the receiver. The RED LED on the receiver          will indicate the receiver is receiving commands from the transmitter. The receiver/transmitter          binding will not have to be repeated, unless one of the two is replaced. Warning: Battery or servos are NOT to be plugged into side ports (A1/A2/Rx), otherwise damage may occur. 2.2 Range check     A pre-flight range check should be done before each flying session. Reflections from nearby metal fences, concrete buildings or trees can cause loss of signal both during range check and during the flight.     The following steps are to be followed to perform the range check of the model before the flight:     1) Place the model at least 60cm (two feet) above non-metal contaminated ground (e.g. on a wooden bench).     2) The receiver antennas should be separated in the model, and do not touch the ground.     3) Place the antenna of the transmitter in a vertical position.     4) Turn on the transmitter and the receiver, press the F/S button of the transmitter module for 4 seconds to enter range check mode, the RED LED of the transmitter module will be off, GREEN LED will flash rapidly, and the beeper will sound. The effective distance will be decreased to 1/30 of full range.     5) Walk away from the model while simultaneously operating the controls on the transmitter, confirming that all controls operate normally to a distance of at least 30 meters (~30 yds).     6) Press the F/S button of the transmitter module for 1S-4S to exit range check mode, RED LED will be back on, indicating normal operation is back. 2.3 Setting failsafe     Failsafe is a useful feature in which all controls move to a preset position whenever the control signal is lost for a period of time. D8R-II plus supports failsafe function for all channels.     Follow the steps below to set failsafe positions for each channel:     1) Bind the receiver first and turn on both the transmitter and the receiver;     2) Move the controls to the desired failsafe position for all channels;     3) Press briefly the F/S button on the receiver (less than 1 second). The transmitter module will make a long “beep”, indicating the failsafe position has been set in the receiver.     To disable the failsafe function, re-bind the receiver. 2.4 LED status RED LED GREEN LED Mode On Dimly On Normal Operation Blinking Off No Signal Blinking On Binding Successful 2.5 Pins definition for side ports     It should be noted that 3.3V only has a limited driving current (1~10mA), it should not be used for driving a MPU. 2.5.1 Two external analog telemetry ports (A1&A2) and one digital data-stream port (Rx). G G G Tx X X Rx A2 A1       Rx: input to receiver, RS232 level, connect with FrSky sensor hub                   A2 (external): max voltage 3.3V, division ratio 1:1                   A1 (external): max voltage 3.3V, division ratio 1:1 2.5.2 When side port pins of A1 and X are connected by the jumper, A1 will change from external analog telemetry port to internal built-in battery voltage sensor. G G G Tx X X Rx A2 A1       Rx: input to receiver, RS232 level, connect with FrSky sensor hub                   A2 (external): max voltage 3.3V, division ratio 1:1                   A1 (internal): max voltage 3.3V, division ratio 4:1   3. How to switch between two PPM mode s     Turn the transmitter off, connect the battery to the receiver, press the F/S button of the receiver for 6 seconds and then release. The red LED will flash fast in HS mode and slowly in FS mode.     The mode alternates each time this procedure is done. Warning: HS mode is only applied for high-speed digital servos. Other servos should select FS mode, otherwise servos will get hot and may burn out.  

Products are shipped by the individual Fruugo retailers, who are located across Europe and the rest of the world. The delivery times and shipping prices vary depending on the retailer's location, the destination country and the selected delivery method.

Fruugo offers two delivery options: Standard or Express. All retailers offer a standard delivery service, and some retailers also offer an express delivery service.

Although Fruugo retailers endeavour to deliver within these timescales, please note that the above timescales are estimated and not guaranteed.

The delivery timescales do not include any customs clearing times beyond Fruugo's control.

Please allow additional shipping time for deliveries to exceptional locations that are hard to reach, and also during busy periods such as Christmas.

All carriers deliver during normal business working hours and may require a signature on receipt, so please ensure your order is delivered to an address where someone will be available to accept it.

We do our best to ensure that the products that you order are delivered to you in full and according to your specifications. However, should you receive an incomplete order, or items different from the ones you ordered, or there is some other reason why you are not satisfied with the order, you may return the order, or any products included in the order, and receive a full refund for the items.

Certain products purchased at Fruugo cannot be returned. They fall in the following categories:

Please take reasonable care of the goods whilst in your care. Any goods returned must be in a resaleable condition. They must be unworn/unused with original tags attached and in original packaging. It is your responsibility to ensure that the goods are appropriately packaged to ensure they are not damaged in return transit.

Notifying us of a return

If you wish to return an order, or some of the products included in an order, please notify Fruugo customer care within 14 days of receiving the goods, including the following information:

Our customer care will send you specific instructions on how to ship the return package(s) to the retailer(s). Please do not ship the return package before you receive the instructions.

Shipping products back to retailers

Goods must be returned without undue delay and in any event not later than 14 days after notifying us of your cancellation.

If you are returning products to several retailers, you should distribute the products accordingly and send the products to those retailers who shipped them to you initially. 

We strongly recommend that you use registered mail (and insure any high-value packages), since neither Fruugo nor the retailer take responsibility for shipments that are lost or damaged during return transportation.

Please ensure you retain a proof of postage receipt so in the unlikely event your parcel goes missing, you will have proof you sent it.

Refunds

You will be refunded within 14 days of the retailer receiving back the goods. We will notify you by e-mail once the products reach the retailer and are accepted for return. Where a retailer has offered to collect the goods, you will be refunded within 14 days of cancelling your contract.

Unless a product or products you wish to return arrived to you damaged or faulty, you are responsible for the return transportation costs.

Providing you are returning all the products from a specific retailer, we will refund the standard shipping costs you paid for the original delivery. If you chose to pay for a non-standard delivery, we will only refund the cost of our least expensive, standard delivery. 

Damaged or faulty goods

If you receive a damaged, broken, or defective product, please notify Fruugo customer care as soon as possible. Include at least the following information:

We will generally instruct you to ship the damaged product back to the retailer. As soon as it reaches the retailer, they will send you a replacement product. If the replacement can't be made, or if you wish to cancel the order, you will be refunded in full. You will also be reimbursed for reasonable returns postage costs for damaged or faulty goods once we have received your postage receipt.

If the outer packaging of your order is clearly damaged on arrival, and you are suspecting that the products are damaged as well, you can either reject the delivery or accept the goods and sign for them as damaged. In both instances, please notify Fruugo customer care as soon as possible.

Refusing delivery

If you refuse to accept delivery of all or part of your order (where the products or packaging do not appear to be damaged or defective) you will be responsible for the postage charges. Any fees and charges incurred by the retailer due to a package being refused will be deducted from your merchandise refund.

 

More FrSky products